... I'll nip along after work.

Re. The radiator top mounts, I'll have another look, as it does look like the radiator is sitting too low for the rubber mounts to be doing anything useful; the radiator is free to wiggle forward and back as much as it likes at the moment.

Just noticed one of my ...

... www.g8dhe.net/bwm/ .
Else if not clean the switch https://www.youtube.com/watch?v=tX1SB0xoJOU

If they are OK and its bleeping, then check the rubber seal isn't stuck to the roof with age, run a card around to release it.
If that is OK then operate the Up then Down switch LOTS of times, it might ...

Yes it sounds like the motors are stalling due to being unable to raise the roof. Often its down to the rubber seal sticking to the roof, the two front corners are likely areas, there should be plastic pads attached to the roof to stop this happening but sometimes they are missing and the rubber then ...

... Now press Up the bleeping should start ??
If not then check the fuses (not likely but easy to do).
If they are OK and its bleeping, then check the rubber seal isn't stuck to the roof with age, run a card around to release it.
If that is OK then operate the Up then Down switch LOTS of times, it might ...

... length which props the roof up. I now know I'm never going to be stuck with the roof in the up possition. The roof when traveling is held dow with rubber ball and socket straps.
The only problem I have is...... the roof alarm will not shut up.....!!!!
Does enyone know how to shut it up without ...

The preferred method is vacuum filling, provided the rubber pipes are in good condition and won't split when the vacuum is applied and then the coolant added to fill the now empty space with minimal air left in the pipework.
Do bear in mind however that the Friendee/Freda vehicles tend to suffer ...

The T Piece came from Halfords 5mm equal Tee. Halfords part No. FIXG229 and a couple of metres of 5mm internal dia rubber hose along with jubilee clips. As mentioned before, cut into the pipe leading from head to Turbo. I actually replaced this pipe with new and fitted the T piece so the horizontal ...

The T Piece came from Halfords 5mm equal Tee. Halfords part No. FIXG229 and a couple of metres of 5mm internal dia rubber hose along with jubilee clips. As mentioned before, cut into the pipe leading from head to Turbo. I actually replaced this pipe with new and fitted the T piece so the horizontal ...

... gaskets and seals, crankshaft seal, water surge tank gasket, water pump, thermostat, both temperature gauges, glow plugs, prettymuch all of the rubber hoses and a couple of metal pipes. The whole engine was out and split etc so egnerally anything that needed addressing, got addressed.
The new ...

If someone has looked after their Bongo, they will clearly be stating it in the sale. looked after is in my opinion:

Changed all the rubber and metal pipes on the diesel engine, maybe cut the rear heater out of the cooling system.
(and has receipts to prove it all)
Undersealed it within the last 3-4 ...

I see, good to understand

And sticking the insulation over the metal plate (fuel tank access?) and rubber plugs is ok?

... so really just want to check my choice of insulation is correct/acceptable, and that sticking it down over the entire floor is ok - covering the rubber bungs and the metal plate?

This insulation does state ‘reduces condensation’ but you think it’s a no to insulating the side panels?

https://www ...

... covering the metal plate (fuel tank access?) - just straight over all the unevenness of the floor, then carpet on top.
There are also little rubber plugs all over the floor that must be there for a reason (drain plugs?) - i’m thinking those who Lino or ply the floor cover these anyway - so is ...

I had the same thing happen with another diesel I had, I went to a scrapyard and sourced another oil cooler and connected the rubber pipes to that and fashioned a bracket which I fitted beneath the original, worked fine till I sold the vehicle on.

Basically they're just a small radiator, the original ...

Depends on year/model refer to the mechanical diagrams for the year, the lights are under the electrical section https://www.lushprojects.com/bongopartsmk2/