Page 1 of 1
					
				Advise re, Head gasket replacement
				Posted: Sun Jul 08, 2007 10:44 am
				by M&K
				Greetings,  I have an oil leak on the drivers side of the engine , near the front, my local garage ( Birmingham ) are good but not familiar with Bongo's. They have looked at the problem and said the head gasket needs replaceing which will also require the head to be skimmed, but are unable to give me a price untill they have thought about it, I have Printed out the Head Gasket info from the club newsletters which I will give to them but  can any one give me advice on the possible cost I should be looking at and/or any information which may help ?
Regards, Mike.
			 
			
					
				
				Posted: Sun Jul 08, 2007 1:02 pm
				by francophile1947
				No idea of cost, but unless it's a bad oil leak(i.e.dripping from engine), or engine isn't running well, I'd be tempted to leave well alone.
			 
			
					
				
				Posted: Sun Jul 08, 2007 4:35 pm
				by nfn
				I would get a second opinion, preferably from a mechanic who knows bongos. Surely if the head gasket is leaking there will be at least a few other symptoms of a failing head gasket -- exhaust gases in coolant, losing coolant, blue smoke from exhaust pipe, etc. Maybe the oil leak is coming from the valve cover gasket if it's leaking out over the front of the engine.
			 
			
					
				
				Posted: Sun Jul 08, 2007 5:04 pm
				by dreamwarrioruk
				our gasket is leaking, i would think that a lot of bongos with have some oil leaks to some extent. im not burning oil and wouldnt consider removing the head unless i get a seroius problem. about 180 for the gaskets and bolts and i think about half a day to strip off head diy, dont know how much a garage would charge but like franco said if it aint too bad leave it alone.
			 
			
					
				
				Posted: Sun Jul 08, 2007 6:27 pm
				by bongoing-mad-simon
				hi m&k
here is a copy of my bill 
 
good luck in finding the problem
___________
simon
I'm bongoing mad! R U?
 
			
					
				
				Posted: Sun Jul 08, 2007 6:43 pm
				by haydn callow
				If its just a black gunge just below the rocker cover/cly head near the front. They nearly all have that and don't worry. If it is fresh oil dripping down than thats a different matter.
			 
			
					
				
				Posted: Sun Jul 08, 2007 6:50 pm
				by bongoing-mad-simon
				as hayden has said i have the same black gunk and as you see i've had a new head.
_____________
simon
I'm bongoing mad!R U?
			 
			
					
				
				Posted: Sun Jul 08, 2007 6:58 pm
				by haydn callow
				The black gunge doesn't actually come from the cyl head gasket. It comes from a rubber seal in that area
			 
			
					
				
				Posted: Sun Jul 08, 2007 7:03 pm
				by nfn
				Mike,
Did the mechanic do a pressure test of the cooling system and/or engine compression test? These tests would confirm the diagnosis of a leaking head gasket. Oil leaking to the outside is not such a problem, unless it's a big leak.
			 
			
					
				
				Posted: Sun Jul 08, 2007 7:19 pm
				by bongoing-mad-simon
				hayden, 
had head cos had over-heating probs ,i think gunk is somthing to do with egr but not sure.
____________
simon
I'm bongoing mad! R U?
			 
			
					
				oil leak
				Posted: Sun Jul 08, 2007 8:49 pm
				by tomsk
				Dear M & K
I too thought my head gasket was leaking, drivers side near the front top of the block etc.
My mechanic says it is the inlet manifold gasket, and I will have it replaced later this year.
I have been to Europe with it like this twice this year, and going again in two weeks, no problem.
I see others on the forum who have had the same leak.
Really need to get it checked out first.
Just a thought?
Regards
Tomsk[/url]
			 
			
					
				Advise re, Head gasket replacement
				Posted: Mon Jul 09, 2007 11:31 pm
				by M&K
				Many thanks to you all for your advice and thoughts regarding my oil leak, there is plenty to think about, a presure test is a good start but if Simons bill is about the average i ceartainly will not be going down that road unless i have to.
Best Regards,  Mike
			 
			
					
				
				Posted: Tue Jul 10, 2007 10:45 pm
				by prb007
				Just had head & gasket changed.
Head.........300quid - eBay
Gasket set; eBay.....50quid
Press. teast 40 quid.
Labour 200 quid - my mate.
Total .....600-ish.
still got probs, though....
http://www.igmaynard.co.uk/bongo/forum/ ... hp?t=12931