HELLO EVERYBODY!!!!!!!!!

vincie1979 · Post by **vincie1979** » Thu Jan 13, 2011 6:41 pm

hello everyone just like to say a quick hello to my fellow bongo owners, ive had my bongo for one month now i brought it for me and my little son of 4 years old who is learning to do motocross and we needed a van and a car so the bongo looked like the right choice (2IN1). ive had quite a few issues with it first it was a cv joint then a wheel bearing then a faulty oil filter leaking and now ive got the dreaded HOLD FLASH LIGHT on, ive tryed looking at the bongo fact sheets about trying to find out what code it is and its says depending on how many times the hold light flashes when diagnosing the problem, some of the code numbers range from code 1 all the way to code 60 somthing NOW does this mean the hold light flashes 1 time or 60 times ect... depending on the fault???????? this i dont know and would really be greatfull if anyone could help me on this matter as i really need to get this problem sorted as its driving me mad and i dont dare drive it with this hold light flashing.PLEASE SOMONE HELP ME THANKS

francophile1947 · Post by **francophile1947** » Thu Jan 13, 2011 7:06 pm

Welcome to the madhouse

Have a read of this http://www.igmaynard.co.uk/bongo/forum/ ... =3&t=29471 - there may be somebody near you who could help. Have you done the wiring work to the ECU to check the flashing light signals? If so, what are the readings?

vincie1979 · Post by **vincie1979** » Thu Jan 13, 2011 10:11 pm

hi there thanks for reply, no i havnt yet done the wire thing, im still not to sure how to read the flashing hold light, it says there are many fault codes ranging from 1 flash to 60 somthing flashes is this right?? ive got an idea how to wire to the ecu but im not sure how to read the flashing bit!!!

Post by **westonwarrior** » Thu Jan 13, 2011 10:43 pm

Hi and welcome
the code flashes in sequence like 6 fast flashes pause 3 slow flashes = 63 long pause then the next number
However I remember it being the oposit but thats probably my memory

is it on all the time or flashing?

Post by **Bob** » Thu Jan 13, 2011 11:19 pm

Welcome aboard.

vincie1979 · Post by **vincie1979** » Fri Jan 14, 2011 3:53 pm

ive just done the wire thing and its flashing 7 times. and i think its a speed sensor whatever that means????? is it a big problem and or how do i get it fixed many thanks for all your help?????????

Post by **g8dhe** » Fri Jan 14, 2011 4:08 pm

You don't say which vehicle you have but assuming its a Diesel then the Speed Sensor is shown as B2-18 and its connector is located here;

Otherwise go to the Index pages at the rear and look up Speed Sensor and select the correct engine type!

Post by **aitch** » Fri Jan 14, 2011 8:41 pm

Welcome to the forum - sorry too techy for me to help but hope you get it fixed soon.

Post by **westonwarrior** » Fri Jan 14, 2011 11:12 pm

thread continues here

http://www.igmaynard.co.uk/bongo/forum/ ... 17&start=0

locking this one to aid continuity

HELLO EVERYBODY!!!!!!!!!

HELLO EVERYBODY!!!!!!!!!

Re: HELLO EVERYBODY!!!!!!!!!

Re: HELLO EVERYBODY!!!!!!!!!

Re: HELLO EVERYBODY!!!!!!!!!

Re: HELLO EVERYBODY!!!!!!!!!

Re: got the code i think lol!!!!!!

Re: HELLO EVERYBODY!!!!!!!!!

Re: HELLO EVERYBODY!!!!!!!!!

Re: HELLO EVERYBODY!!!!!!!!!